Herramientas para instalación de vinilo

Ver como

Most bad installs are not caused by bad hands. A dry felt drags scratches across a gloss panel, a dull blade tears the film instead of cutting it, a heat gun that spikes cooks the finish, and a magnet slips just when the film needs holding. TeckWrap tools come from the same team that makes the film, so every squeegee, blade and heat gun is built around how vinyl, PPF and window tint actually behave on a car. Start with a complete master set or add the one tool your kit is missing, and spend less time fixing and more time finishing.

Master Sets by Film Type

Vinyl, PPF and tint each go on differently, so each needs a different squeegee and a different routine. A master set puts the right tools for one film type in a single order.

SetHow the film goes onTools that matter mostShop
TeckWrap vinyl wrap installation master setVinyl Wrap Master SetColor change filmDry, with heat to stretch and post-heatFelt-edged squeegees, fresh buffers, tucking tools, magnets, a safety cutter and a heat gunVinyl Master Set
TeckWrap PPF installation master setPPF Master SetPaint protection filmWet, with slip and tack solutionFirm PPF squeegees, a rubber squeegee, a pressure sprayer and installation liquidPPF Master Set
TeckWrap window tint installation master setWindow Tint Master SetWindow filmWet, on the inside of the glass, with heat shrinking on curved glassRubber tint squeegees, triangle scrapers for tight edges and a heat gun for shrinkingTint Master Set

Tools by Category

Building your own kit, or replacing a worn tool? Every tool in the collection fits one of these jobs.

CategoryWhat it doesShop
TeckWrap multi-color squeegee set for vinyl wrapSqueegees and ScrapersLay the film down and push out air or solution. Softer edges suit vinyl, firmer polyurethane and rubber suit PPF and tint. Fresh buffers keep the face of the film free of scratches.Multi-Color Squeegee Set
PPF Squeegee Set
Tint / PPF Rubber Squeegee
Triangle Tint Scraper
Buffers (10 pieces)
TeckWrap safety cutter with concealed bladeKnives and BladesTrim edges, cut relief cuts and split liner. Safety cutters keep the blade covered, and snap-off SK5 blades give a sharp edge for every panel.Safety Cutter
Utility Knife (9mm)
Utility Knife (18mm)
SK5 Blades
Round Corner Blades
TeckWrap High-Performance Heat Gun with digital displayHeat GunsSoften film to stretch it, shrink tint on curved glass, post-heat edges and lift old film for removal.High-Performance Heat Gun
Standard Heat Gun
TeckWrap tucking tool set for vinyl wrap edgesEdges and DetailsTuck film into panel gaps, behind seals and around trim, and release trapped air without lifting the film.Tucking Tool Set
Air-Release Pen
Contour Soft Squeegee
TeckWrap vinyl wrap magnetsPositioning and PrepHold film in place, measure panels, keep fingerprints off the adhesive and wet the surface for PPF and tint.Wrap Magnets
Soft Measuring Tape
Premium Gloves
PPF Pressure Sprayer
PPF Installation Liquid
TeckWrap tool pouchStorageKeep squeegees, knives and blades on your belt during the job and protected between jobs.Tool Pouch
Toolbox

High-Performance vs Standard Heat Gun

Both guns reach 650 °C. The difference is how precisely, and how low, you can set the heat.

FeatureHigh-Performance Heat GunStandard Heat Gun
Temperature50-650 °C with a digital display100-650 °C with step-less control
Airflow and power2000 W, 6 airflow speedsDual heating coils for faster heat-up
ExtrasRemembers your last setting, copper motor, heat-resistant nozzle sleeveOverload protection, built-in heat shield
PlugsUS, EU, UK, CN and AUUS, EU, UK, CN and AU
Best forDaily shop use, and the low settings PPF and tint shrinking needDIY projects and a second gun in the shop

Looking After Your Tools

  • Swap a buffer as soon as it picks up grit or wears thin. A worn buffer scratches the film you are trying to protect.
  • Snap the blade to a fresh edge often. A dull blade drags, tears film and needs more pressure, which is how paint gets cut.
  • Wipe squeegee edges clean after each job and check them for nicks before the next one.
  • Let a heat gun cool with the airflow running before you put it away, and store it dry.

Vinyl Wrap Tools FAQ

Can I use the same squeegee for vinyl, PPF and tint?

Not ideally. Vinyl goes on dry, so a felt or buffered edge protects its face. PPF and tint go on wet and need a firmer polyurethane or rubber edge to push the solution out from under the film. Using the wrong one leaves either scratches or trapped water.

What temperature should I set my heat gun to?

Follow the post-heat temperature in your film's technical data sheet, because it changes from film to film. Start low, keep the gun moving and hold it a few inches from the surface. Too much heat burnishes matte and satin films and damages chrome.

Which knife should I use on a car?

For trimming film and splitting liner, a safety cutter keeps the blade covered. For detailed trimming, a 9mm knife with a sharp 30° blade gives the most control. Keep cutting pressure light and never cut directly against paint.

Is a master set worth it over buying tools one by one?

If you are starting out or adding a new film type to your shop, yes. Each set covers the core tools for one kind of install in a single order. If you already have a working kit, buy the single tools you need to replace.