ग्लॉस मेटैलिक बरगंडी ब्लैक विनाइल रैप (HM10-HD)

Film construction

• Film type: Renolit hybrid polymeric film with air-release channels
• Series: 190 Series
• Film thickness: 0.15 mm
• Liner thickness: 0.13 mm
• Total thickness with liner: 0.31 mm
• Liner: transparent plastic release liner with air-release grid pattern
• Adhesive: Henkel solvent-based acrylic, transparent, ultra weather-resistant, 1000 to 3000 cps viscosity, 12 μm dry
• Finish: gloss metallic, directional
• Roll width: 1.52 m (5 ft)
• Roll length: 18 m (59 ft)
• Roll weight: 13 kg

Performance

• Service range: -35°C to +35°C
• Surface gloss CD: 14.5% (ASTM D523-99, 60° angle)
• Tensile strength: MD 29.5 / CD 24.8 N/mm² (ASTM D882-02)
• Elongation at break: MD 206.8 / CD 196.4 (ASTM D882-02)
• Dimensional stability: 2% shrinkage at 70°C (ASTM D1204-02)
• Surface tension: 34 dynes/cm (ASTM D2578-04a)
• Storage: 2 years at +10°C to +20°C, 50% RH, in original packaging, away from direct sunlight

Warranty

Built for long-term outdoor use, with up to 3 years of durability on vertical panels and around 2 years across a full wrap, depending on climate zone. Horizontal surfaces such as roofs, hoods, and bonnets take the most sun and weather and carry a shorter expected life. The warranty covers manufacturing defects such as bubbling, cracking, and adhesive failure when the film is properly stored, professionally installed, and maintained per the care guidance. It does not cover abrasion, scratches, gloss change, or normal wear. Heat-removable within 2 years for the cleanest removal, with minimal adhesive residue.

• Surface: apply only to a clean, sound, fully cured OEM factory finish. Repainted, primed, aftermarket, or damaged surfaces can affect adhesion and removal and fall outside warranty coverage.
• Apply at +17°C to +23°C
• Tools: squeegee, buffer, knife, masking tape, heat gun, magnets, gloves, IR thermometer
• Conformability: smooth and medium-curved surfaces
• Post-heat: 100°C
• Cure: 24 hrs above 10°C (48 hrs at room temperature recommended)
• Overlap: 3 to 4 mm
• Directional film, especially metallic colors. Keep film orientation consistent across all panels and use one production LOT per vehicle to avoid color shift between panels.
• Avoid overstretching during application
• Remove the protective cap before installing
• Professional installation strongly recommended for the best result and to keep the warranty valid
• Aftercare: hand wash with a pH-neutral shampoo (pH 3 to 11). Avoid waxes, solvents, and petroleum-distillate products, and never use automatic washes, brushes, or high-pressure washers.

All TeckWrap statements, technical information, and recommendations are based on tests believed to be reliable but do not constitute a guarantee or warranty. All products are sold with the understanding that the buyer has independently determined the suitability of the products for their purpose.

TeckWrap products are warranted to be free of defects in material for the period of shelf life. In case of defects, TeckWrap will replace the product or compensate at its sole discretion. This is the exclusive obligation of TeckWrap Inc.

Warranty does not cover normal wear, transportation, labor, or consequential damages. Coverage requires proper storage, professional installation, and maintenance in line with TeckWrap's care guidance, and does not apply to films installed on non-OEM, repainted, or damaged surfaces. If you notice cracking, lifting, edge failure, or other defects, contact your installer promptly for assessment.

Removal from aged, repainted, or poorly bonded factory paint may lift paint or clear coat. TeckWrap is not responsible for the condition of the underlying paint upon removal.

Aftermarket waxes, sealants, and ceramic coatings are applied at the owner’s discretion. Damage caused by aftermarket products is not covered.

Screen images may vary, refer to physical color swatches. Use the same production LOT for color consistency. Scratches during application or daily use are not covered.