SKU: VCH423-S-18M

Satin Gable Green Vinyl Wrap (VCH423-S)

(2)
$ 7,762.00 $ 11,652.00
Tax included Shipping calculated at checkout.

Description

Gable Green hides in plain sight. In low light it reads almost dark, a deep, blackened forest green with a blue undertone pulling it darker still, and only when direct light finds it does a cold emerald surface through the satin, with a faint teal in the reflections. It's never bright and never loud, this is gemstone green, the dark emerald of a watch dial rather than a sports-car green, and the restraint is the whole point.

Key Attributes

  • Near-black until it's lit: a blackened forest-green base with a blue undertone that reads almost black in low light, then lifts to a cold, controlled emerald where direct light hits.
  • Gemstone satin metal: a silver-coated metalized film under the green tint gives jewel-like depth and a faint teal in the reflections, forged-metal richness kept to a quiet satin, never candy-bright.
  • Metalized, treat it gently: directional film that rewards an experienced installer, keep panel orientation consistent, and avoid the crumpling, overstretching, or excess heat that can disturb the metal layer.
  • Flat lay, low orange peel: a premium release liner sets the film down smooth, while Henkel solvent acrylic adhesive with air-release channels pushes trapped air out across big panels.
  • Paint-safe removal: stays weatherproof for the life of the wrap and heat-removes cleanly, leaving the factory finish underneath as it was.

Gable Green keeps its secrets in shadow. Parked in a garage or under overcast sky it can pass for black, only the faintest green edge giving it away, step it into sun and a deep, cold emerald rises through the satin, teal flickering in the brightest reflections. It never gets loud about it, the green stays controlled and gemstone-deep rather than vivid, closer to a jewel than a paint chip. The satin diffuses the metallic so the surface reads liquid and expensive, the kind of finish that looks commissioned rather than picked from a chart. 

OEM Match

  • Tracks satin Porsche Jet Green Metallic almost exactly the same dark, cold emerald depth.
  • Sits right alongside a heritage BMW Oxford Green.
  • Shares the coachbuilt character of Bentley's dark commission greens and Aston Martin's racing greens.
  • Edges toward classic British Racing Green in the lowest light.
  • Deeper and more blackened than a brighter emerald exotic green.

These are the heritage and coachbuilt greens that live on grand tourers and flagship SUVs, not sports coupes. TeckWrap Gable Green puts that watch-dial emerald on a DB12, a 911 Turbo, a Continental GT, a Range Rover, or any car that wears depth well, no bespoke commission required.

Features

Film Construction

  • Film Type: Polymeric hybrid film with silver coating and air-release channels
  • Series: 180 series
  • Film Thickness: 0.15 mm
  • Backing Liner Thickness: 0.17 mm
  • Total Thickness (with liner): 0.32 mm
  • Liner: Felix Schoeller 20-104-20-1,9, double-sided PE-coated Kraft, one side solventless silicone-coated, air-release (ISO 9001, ISO 14001, OHSAS 18001)
  • Adhesive: Henkel solvent-based acrylic, transparent, ultra-weather-resistant, viscosity 1000–3000 cps, 12 µm dry
  • Finish: Satin, directional
  • Roll Width: 5 ft (1.52 m)
  • Full Roll Length: 59 ft (18 m)

Performance

  • Service range: -35°C to +35°C
  • 180° peel strength: 10.66 N/25mm (standard ≥6.8)
  • Initial tack: 822 g/25mm (standard 800–1500)
  • Release force: 0.1 N/25mm (standard 0.10–0.30)
  • Adhesion: 70, no shifting (standard ≥60)
  • Aging tested +65°C and -65°C: no adhesive residue
  • Storage: 2 years at +10°C to +20°C, 50% RH, in original package, away from direct sunlight

Warranty

  • Built for long-term outdoor use, up to 3 years outdoor durability on vertical panels and around 2 years across a full wrap, depending on climate zone. Heat-removable, with minimal adhesive residue when removed within the recommended three years.
  • Metalized films require careful handling. The appearance of the metalized layer can change with crumpling, overstretching, or excessive heat. The film may scratch during application or daily use. The warranty does not cover the scratching of the film.

Application
  • Apply at +17°C to +23°C
  • Tools: soft squeegee with buffer, knife, masking tape, heat gun, magnets, gloves, IR thermometer, IR heater
  • Conformability: smooth and medium-curved surfaces, avoid overstretching
  • Directional film, check orientation before cutting
  • Overlap: 3–4 mm
  • Post-heat: 95°C
  • Cure time: 24 hours above 15°C; 48 hours at room temperature recommended for maximum adhesive activation
  • Handle the satin chrome surface carefully; it can scratch during installation

Disclaimer

All TeckWrap statements, technical information, and recommendations are based on tests believed to be reliable but do not constitute a guarantee or warranty. All products are sold with the understanding that the buyer has independently determined the suitability of the products for their purpose.
TeckWrap products are warranted to be free of defects in materials for the shelf life period. In case of defects, TeckWrap will replace the product or compensate at its sole discretion. This is the exclusive obligation of TeckWrap Inc.
Warranty does not cover normal wear, transportation, labor, or consequential damages.
Screen images may vary; refer to physical color swatches. Use the same production LOT for color consistency. Film must be stored without the protective layer to prevent tunneling. Scratches during application or daily use are not covered.

Valuable Advices

View all
  • DIY vs. Professional Window Tint Installation

    DIY vs. Professional Window Tint Installation

    Nothing changes a vehicle's personality quite like a dark smoky tint. But it can be expensive forcing you to choose between DIY installation and hiring a professional? DIY window tinting...

    E. Adnan |

  • How To Wrap Taillights

    How To Wrap Taillights

    Wrapping your taillights with a tint PPF is one of the simplest upgrades you can make to give your car a bold, smoky look. This step-by-step guide covers everything, from...

    E. Adnan |

  • Common Mistakes When Applying Color PPF

    Common Mistakes When Applying Color PPF

    Applying color paint protection film (PPF) can be tricky, and mistakes during the installation process can lead to bubbles, creases, and poor adhesion. Learn about the 5 most common color...

    E. Adnan |

  • When to Use Adhesive Promoters and Tack Reducers?

    When to Use Adhesive Promoters and Tack Reducers?

    Installing a car wrap isn’t just about applying vinyl—it requires skill, precision, and the right supporting products. Adhesive promoters help strengthen vinyl grip on tricky edges and curves, while tack...

    Nicki Ammelung |

  • Common Causes of Vinyl Adhesion Failure

    Common Causes of Vinyl Adhesion Failure

    Avoid Car Wrap Lifting & Peeling – Get a Flawless Finish Every TimeDIY vinyl wrapping can be challenging, and adhesion failure is one of the most common issues. From poor...

    Shukhrat Ismatov |

  • Wrapping a Rusty Car: Is It Possible?

    Wrapping a Rusty Car: Is It Possible?

    Car wrapping has exploded in popularity, offering a dynamic way to personalize vehicles. But what happens when the canvas isn't pristine? Can you successfully wrap a car with rust or...

    Phyllis Li |

  • How to Wrap a Car in Winter Time

    How to Wrap a Car in Winter Time

    Wrapping a car in vinyl during winter can be challenging due to cold temperatures, but with the right preparation and tools, you can still achieve a professional finish. Work in...

    Vasile Sayfutdin |