Sku: CG46-HD-5M

高光撒哈拉米色乙烯基贴膜 (CG46-HD)

(2)
正常价格 ¥1,577.00
船运 在结帐时计算。

描述

许多米色包膜在阳光直射下会显得像泥土般的棕褐色或黄色。而TeckWrap的“撒哈拉米色”则呈现出温暖的香槟沙色调,随着光线的变化,其中会透出奶油色和蜜桃色的光泽。 

主要特性

  • 温暖而不显单调:香槟沙色基调会呈现奶油色与蜜桃色的渐变,而非转变为单调的棕褐色。 
  • 耐候性强:透明的汉高(Henkel)溶剂型丙烯酸胶粘剂,经得起恶劣天气的考验。 
  • 无气泡安装:聚合物混合薄膜带有排气通道,铺贴平整,无气泡或气囊。
  • 平整铺贴,完美收尾:高品质PET离型纸确保贴膜过程中薄膜平整,呈现均匀表面。 
  • 热塑性:可紧密贴合镜面、曲面、边缘及中等深度的凹陷面板,不会剥离或翘起。
  • 保护原车漆:胶粘剂可干净剥离,不会损坏原厂漆面。

TeckWrap的“撒哈拉米色”会随着光线变化在奶油色、蜜桃色和香槟色之间流转,绝不会固定为单一色调。其设计灵感源自奢华砂岩、沙漠阳光以及抛光香槟色陶瓷。直射阳光下,香槟色调更为明亮;阴天时,则呈现出更浓郁的沙漠米色。这种色调在整车表面始终保持着层次感与动态美感,与黑色饰条、青铜色轮毂及深色车窗玻璃自然相配。    

原厂色匹配

  • 最接近路虎“缎面香槟”色。  
  • 与宾利Mulliner系列的香槟沙色色调相同。 
  • 比劳斯莱斯“沙漠珍珠”色更浅。 
  • 与梅赛德斯-奔驰MANUFAKTUR香槟沙金属漆具有相同的深度。
  • 饱和度与保时捷“喀什米尔米色”相同。

梅赛德斯-奔驰、劳斯莱斯和宾利均将此色调限定于其顶级配置车型。TeckWrap的“撒哈拉米色”贴膜,可将这一色调呈现于您车道上的爱车之上。

Features

Film Construction

Film Type: Premium polymeric hybrid with air-release channels and Super Gloss HD finish

Film Thickness: 0.14 mm

Release Liner Thickness: 0.03 mm

Backing Liner Thickness: 0.13 mm

Total Thickness (with liner): 0.30 mm

Liner Thickness: 142 µm plastic (HD high-gloss)

Adhesive: Henkel solvent-based acrylic, ultra-weather-resistant, viscosity 1000–3000 cps, 12 µm dry

Top Layer: PET protective layer (peel before heating)

Roll Width: 5 ft (1.52 m)

Full Roll Length: 59 ft (18 m)

Performance

  • Service temperature: -35°C to +35°C
  • Release force: 0.18 N/25mm (standard 0.10–0.30)
  • Initial tack: 1015 g/25mm (standard 800–1500, GB31125-2014)
  • Peel strength (180°): 8.1 N/25mm (standard ≥4.9, GB/T2792-1998)
  • Adhesion strength: 70 (standard ≥60, no shifting, GB/T4851-1998)
  • Aging tested: -65°C to +65°C, no residue
  • Storage shelf life: 2 years at +10°C to +20°C, 50% RH, dry conditions, away from sunlight.

Warranty

  • Built for long-term outdoor use, up to 3 years outdoor durability on vertical panels and around 2 years across a full wrap, depending on climate zone. Heat-removable, with minimal adhesive residue when removed within the recommended three years.

Application

  • Application temperature: +17°C to +23°C
  • Tools: squeegee with buffer, knife, masking tape, heat gun, magnets, gloves, IR thermometer, IR heater
  • Conformability: smooth and medium-curved surfaces
  • Post-heat: 95–100°C (gloss finish)
  • Cure: 24 hrs above 10°C (48 hrs at room temperature recommended)
  • Overlap: 3–4 mm
  • Non-directional film
  • Avoid overstretching during application
  • Remove the protective cap before installing
  • Aftercare: pH-neutral products only, avoid hot wax or strong solvents

Disclaimer

All TeckWrap statements, technical information, and recommendations are based on tests believed to be reliable but do not constitute a guarantee or warranty. All products are sold with the understanding that the buyer has independently determined the suitability of the products for their purpose.


TeckWrap products are warranted to be free of defects in materials for the shelf life period. In case of defects, TeckWrap will replace the product or compensate at its sole discretion. This is the exclusive obligation of TeckWrap Inc.
Warranty does not cover normal wear, transportation, labor, or consequential damages.
Screen images may vary; refer to physical color swatches. Use the same production LOT for color consistency. Film must be stored without the protective layer to prevent tunneling. Scratches during application or daily use are not covered.