Sku : CG02-HD-5M

슈퍼 흰색 (CG02-HD) 비닐 랩

(2)
정가 ₩358,000
해운 결제시 계산.

설명

Teckwrap은 차량에 견고하고 반짝이는 마무리를 제공하는 새로운 광택 HD 색상을 제공합니다. 주황색 껍질이없는 매끄러운 표면 으로이 고화질 랩은 ​​모든 프로젝트를 향상 시키도록 설계되었습니다. 재료는 신축성이 높기 때문에 모든 모서리와 오목한 영역을 쉽게 감을 수 있습니다. 또한, 접착제는 안전하고 번거롭지 않고 필요할 때 제거 할 수 있습니다.

PET 보호 층은 설치 중에 필름을 긁히지 않도록합니다 (가열하기 전에 껍질을 벗기십시오). 플라스틱 라이너는 광택과 반사 표면을 보장합니다.

명세서

필름 두께 : 110 μm 

라이너 두께 릴리스 : 142 μm

영화 유형 : 공기 방출 기술을 갖춘 고급 폴리머 캘린더 필름

점착제: 헨켈 용매 기반 아크릴 접착제, 초경량 내성, 점도 1000 ~ 3000cps, 두께 12 μm 건조

릴리스 라이너 : 플라스틱 라이너

저장 기간 : +10 ° C ~ +20 ° C 사이의 2 년, 원래 패키지에서 상대 습도 50%, 직사광선에서 멀리 떨어진 깨끗하고 건조한 곳.
중요 : 설치하기 전에 상단 보호 레이어를 제거하고 "터널링"을 방지하기 위해 필름을 저장하십시오.

내구성/보증 : 데이터 시트를 참조하십시오 (자세한 내용은 링크를 클릭하십시오).

접착력 및 성능 테스트

방출력 (N/25mm) : 표준 0.10-0.30, 결과 0.18 (23 ° C, 54% RH)

초기 압정 (G/25mm) : 표준 800-1500, 결과 1015 (23 ° C, 54% RH)

180 ° 껍질 강도 (N/25mm) : 표준 ≥4.9, 결과 8.1 (23 ° C, 54% RH)

접착 강도 : 표준 ≥60, 결과 70 (이동 없음)

노화 테스트 :

고온 (65 ℃, 7 일) : 접착제 잔류 물 없음

저온 (-65 ° C, 10 일) : 접착제 잔류 물 없음

설치 팁

적용 온도 : +18 ° C ~ +22 ° C

사용 온도 범위 : -30 ° C ~ +45 ° C

필요한 도구 : 소프트 버퍼가있는 표준 스퀴지

적합성 : 매끄럽고 중간 정도의 표면에 적합합니다

방향 : 아니요

겹침 너비 : 3-4 mm

사후 온도 : 95 ° C

중요 : 설치하기 전에 보호 캡을 벗겨냅니다.

메모

화면에 표시된 이미지, 색상 및 마감은 대략적입니다. 정확한 표현을 위해 항상 물리적 색상 견본을 참조하십시오.

약간의 배치 대 배치 색상 변동을 피하기 위해 동일한 생산 로트 번호의 롤을 사용하십시오.

필름은 적용 또는 매일 사용하는 동안 긁힐 수 있습니다. 긁힘은 보증에 적용되지 않습니다.

이 랩은 전문가와 DIY 애호가 모두에게 뛰어난 성능과 미학을 제공합니다. 지금 주문하고 프로젝트를 다음 단계로 끌어 올리십시오!

Features

Film construction

  • Film type: Premium polymeric hybrid with air-release channels and Super Gloss HD finish
  • Film thickness: 110 µm
  • Liner thickness: 142 µm plastic (HD high-gloss)
  • Adhesive: Henkel solvent-based acrylic, ultra-weather-resistant, viscosity 1000–3000 cps, 12 µm dry
  • Top layer: PET protective layer (peel before heating)
  • Roll width: 5ft (1,52m)
  • Full roll length: 59ft (18 m)

Performance

  • Service temperature: -35°C to +35°C
  • Release force: 0.18 N/25mm (standard 0.10–0.30)
  • Initial tack: 1015 g/25mm (standard 800–1500, GB31125-2014)
  • Peel strength (180°): 8.1 N/25mm (standard ≥4.9, GB/T2792-1998)
  • Adhesion strength: 70 (standard ≥60, no shifting, GB/T4851-1998)
  • Aging tested: -65°C to +65°C, no residue
  • Storage shelf life: 2 years at +10°C to +20°C, 50% RH, dry conditions, away from sunlight.

Warranty

  • Built for long-term outdoor use, up to 3 years outdoor durability on vertical panels and around 2 years across a full wrap, depending on climate zone. Heat-removable, with minimal adhesive residue when removed within the recommended three years.

Application

  • Application temperature: +17°C to +23°C
  • Tools: squeegee with buffer, knife, masking tape, heat gun, magnets, gloves, IR thermometer, IR heater
  • Conformability: smooth and medium-curved surfaces
  • Post-heat: 95–100°C (gloss finish)
  • Cure: 24 hrs above 10°C (48 hrs at room temperature recommended)
  • Overlap: 3–4 mm
  • Non-directional film
  • Avoid overstretching during application
  • Remove the protective cap before installing
  • Aftercare: pH-neutral products only, avoid hot wax or strong solvents

Disclaimer

All TeckWrap statements, technical information, and recommendations are based on tests believed to be reliable but do not constitute a guarantee or warranty. All products are sold with the understanding that the buyer has independently determined the suitability of the products for their purpose.


TeckWrap products are warranted to be free of defects in materials for the shelf life period. In case of defects, TeckWrap will replace the product or compensate at its sole discretion. This is the exclusive obligation of TeckWrap Inc.
Warranty does not cover normal wear, transportation, labor, or consequential damages.
Screen images may vary; refer to physical color swatches. Use the same production LOT for color consistency. Film must be stored without the protective layer to prevent tunneling. Scratches during application or daily use are not covered.