Vinylfolie „Color Shift“ in Mattsilber „Sunset“ (DS03M)

Film construction

• Film type: high-grade polymeric multilayered calendered vinyl film with air-release channels
• Series: 190 Series
• Film thickness: 0.16 mm
• Liner thickness: 0.13 mm
• Total thickness with liner: 0.29 mm
• Liner: transparent plastic release liner (0.03 mm) with air-release grid pattern
• Adhesive: Henkel solvent-based acrylic, transparent, ultra weather-resistant, 1000 to 3000 cps viscosity, 12 μm dry
• Finish: matte color-shift (chameleon), directional
• Roll width: 1.52 m (5 ft)
• Roll length: 18 m (59 ft)
• Roll weight: 14 kg

Performance

• Service temperature: -35°C to +35°C
• Dimensional stability: shrinkage less than 3%
• Plastification: 27% to 35%
• Breaking strength: 22.7 N/10mm avg (ASTM D3759/D3759M-05)
• 180° peel strength to steel: 7.4 N/10mm avg (ASTM D3330/D3330-04)
• UV resistance: grade 5, pass (ASTM D4329-13 Cycle A, ISO 105-A02), 49h exposure
• Storage: 2 year shelf life at +10°C to +20°C, 50% relative humidity, in original packaging, away from direct sunlight

Warranty

Matte color-shift is a delicate finish and needs more care than gloss. With proper care and a matte-safe ceramic coating, expect up to 3 years of outdoor durability on vertical panels and around 2 years across a full wrap, depending on climate zone. Parking indoors or under cover extends the finish. Heat-removable within 2 years for the cleanest removal, with minimal adhesive residue.

• Surface: apply only to a clean, sound, fully cured OEM factory finish. Repainted, primed, aftermarket, or damaged surfaces can affect adhesion and removal and fall outside warranty coverage.
• Apply at +17°C to +23°C
• Tools: squeegee, buffer, knife, masking tape, heat gun, magnets, gloves, IR thermometer, IR heater
• Conformability: smooth and medium-curved surfaces
• Post-heat: 100°C
• Cure: 24 hrs above 10°C (48 hrs at room temperature recommended)
• Overlap: 3 to 4 mm
• Directional film. The color-shift effect orients with the film, so keep orientation consistent across all panels and use one production LOT per vehicle to avoid a mismatched shift between panels.
• Avoid overstretching during application, which can distort the color-shift pigment
• Avoid over-buffing and hard squeegee pressure, which can burnish a matte surface to a shine
• Remove the protective cap before installing
• Professional installation strongly recommended for the best result and to keep the warranty valid
• Aftercare: hand wash with a matte-safe, pH-neutral shampoo (pH 3 to 11). Avoid waxes, polishes, gloss enhancers, solvents, and petroleum-distillate products, and never use automatic washes, brushes, or high-pressure washers.

All TeckWrap statements, technical information, and recommendations are based on tests believed to be reliable but do not constitute a guarantee or warranty. All products are sold with the understanding that the buyer has independently determined the suitability of the products for their purpose.

TeckWrap products are warranted to be free of defects in material for the period of shelf life. In case of defects, TeckWrap will replace the product or compensate at its sole discretion. This is the exclusive obligation of TeckWrap Inc.

Warranty does not cover normal wear, transportation, labor, or consequential damages. Coverage requires proper storage, professional installation, and maintenance in line with TeckWrap's care guidance, and does not apply to films installed on non-OEM, repainted, or damaged surfaces. If you notice cracking, lifting, edge failure, or other defects, contact your installer promptly for assessment.

Matte finishes can burnish to a shine if rubbed, scrubbed, or polished, and show fingerprints and water spots more readily than gloss. Color-shift films also change apparent color with viewing angle and lighting, with the shift following the film orientation. These are normal characteristics of a matte color-shift film and are not covered.

Removal from aged, repainted, or poorly bonded factory paint may lift paint or clear coat. TeckWrap is not responsible for the condition of the underlying paint upon removal.

Screen images may vary, refer to physical color swatches. Use the same production LOT for color consistency. Scratches during application or daily use are not covered.