Sku: CG48-HD-5M

高光西班牙薰衣草色车身贴膜 (CG48-HD)

(8)
正常价格 ¥1,577.00
船运 在结帐时计算。

描述

在强光下,粉紫色往往会呈现出一种粉笔般、塑料般的质感。TeckWrap 高光西班牙薰衣草色则无论是在晴朗的天空下,还是在阴沉的午后,都能保持其乳白色的深邃感与柔和的薰衣草色调。  

主要特点

  • 奶油般的柔和色调:柔和的薰衣草紫色,以乳白色为基底,使色彩呈现出均匀的质感,避免过度偏粉或偏蓝。 
  • 珍珠般的光泽:聚合物多层混合薄膜营造出丰富的反射效果,赋予表面柔和的层次感,且无需依赖厚重的金属闪粉。 
  • 无气泡安装:排气槽在安装过程中将困住的空气排出,确保曲面和车身线条无气泡。
  • 耐候性强:汉高溶剂型丙烯酸粘合剂保持透明,即使在天气变化时也能牢固粘合,边缘不会翘起。  
  • 专为车身线条设计:在受控加热条件下,可包裹后视镜、曲面、保险杠及中等程度的凹陷面板。
  • 拆除不留残留:胶层可干净剥离,不会损坏原厂漆面。

“西班牙薰衣草”既非深紫色,也非粉色系柔和色调。其乳白色基底使其介于两者之间,赋予色彩一种纯净、数字化的特质。在动态光线下,光影反射呈现奶油般的柔和质感而非锐利光泽,更接近抛光瓷器。即使没有直射阳光,它也能保持稳定、可控的柔和感。这种颜色始终保持沉稳,不会因光线变化而改变其特质。

原厂色匹配

  • 最接近日产菲戈拉薰衣草色。
  • 比保时捷“月光石”色更柔和。
  • 饱和度与保时捷“月宝石”相同。

日产早在几十年前就停产了菲戈车型。这款车身贴膜将相同的柔和薰衣草色带到了Model Y、Ioniq 5或Polestar 2上。

Features

Film construction

  • Film type: Premium polymeric hybrid with air-release channels and Super Gloss HD finish
  • Film thickness: 110 µm
  • Liner thickness: 142 µm plastic (HD high-gloss)
  • Adhesive: Henkel solvent-based acrylic, ultra-weather-resistant, viscosity 1000–3000 cps, 12 µm dry
  • Top layer: PET protective layer (peel before heating)
  • Roll width: 5ft (1,52m)
  • Full roll length: 59ft (18 m)

Performance

  • Service temperature: -35°C to +35°C
  • Release force: 0.18 N/25mm (standard 0.10–0.30)
  • Initial tack: 1015 g/25mm (standard 800–1500, GB31125-2014)
  • Peel strength (180°): 8.1 N/25mm (standard ≥4.9, GB/T2792-1998)
  • Adhesion strength: 70 (standard ≥60, no shifting, GB/T4851-1998)
  • Aging tested: -65°C to +65°C, no residue
  • Storage shelf life: 2 years at +10°C to +20°C, 50% RH, dry conditions, away from sunlight.

Warranty

  • Built for long-term outdoor use, up to 3 years outdoor durability on vertical panels and around 2 years across a full wrap, depending on climate zone. Heat-removable, with minimal adhesive residue when removed within the recommended three years.

Application

  • Application temperature: +17°C to +23°C
  • Tools: squeegee with buffer, knife, masking tape, heat gun, magnets, gloves, IR thermometer, IR heater
  • Conformability: smooth and medium-curved surfaces
  • Post-heat: 95–100°C (gloss finish)
  • Cure: 24 hrs above 10°C (48 hrs at room temperature recommended)
  • Overlap: 3–4 mm
  • Non-directional film
  • Avoid overstretching during application
  • Remove the protective cap before installing
  • Aftercare: pH-neutral products only, avoid hot wax or strong solvents

Disclaimer

All TeckWrap statements, technical information, and recommendations are based on tests believed to be reliable but do not constitute a guarantee or warranty. All products are sold with the understanding that the buyer has independently determined the suitability of the products for their purpose.


TeckWrap products are warranted to be free of defects in materials for the shelf life period. In case of defects, TeckWrap will replace the product or compensate at its sole discretion. This is the exclusive obligation of TeckWrap Inc.
Warranty does not cover normal wear, transportation, labor, or consequential damages.
Screen images may vary; refer to physical color swatches. Use the same production LOT for color consistency. Film must be stored without the protective layer to prevent tunneling. Scratches during application or daily use are not covered.