碳纤维拉丝黑乙烯基贴膜 (BM04)

Film construction

• Film type: premium-grade polymeric hybrid film with air-release channels
• Film thickness: 0.16 mm
• Liner thickness: 0.13 mm
• Total thickness with liner: 0.29 mm
• Liner: transparent plastic release liner with air-release grid pattern
• Adhesive: Henkel solvent-based acrylic, transparent, ultra weather-resistant, 1000 to 3000 cps viscosity, 12 μm dry
• Finish: brushed metal texture (carbon brushed), directional
• Roll width: 1.52 m (5 ft)
• Roll length: 18 m (59 ft)
• Roll weight: 14 kg

Performance

• Service temperature: -35°C to +35°C
• Dimensional stability: shrinkage less than 2%
• Storage: 2 year shelf life at +10°C to +20°C, 50% relative humidity, in original packaging, away from direct sunlight

Warranty

This is an accent and trim film for partial application. Used on spoilers, mirrors, roofs, and interior trim, it is built for long-term use with up to 3 years of durability on vertical surfaces and around 2 years on a full panel, depending on climate zone. The warranty covers manufacturing defects such as bubbling, cracking, and adhesive failure when the film is properly stored, professionally installed, and maintained per the care guidance. It does not cover abrasion, scratches, gloss change, or normal wear. Heat-removable within 2 years for the cleanest removal, with minimal adhesive residue.

• Best suited to partial and accent application: spoilers, mirrors, roofs, door trim, and interior elements.
• Surface: apply only to a clean, sound, fully cured OEM factory finish. Repainted, primed, aftermarket, or damaged surfaces can affect adhesion and removal and fall outside warranty coverage.
• Application temperature: +17°C to +23°C
• Tools: standard squeegee with soft buffer, heat gun, knife, masking tape, gloves
• Conformability: smooth and medium-curved surfaces
• Directional film. The brushed grain runs in one direction, so keep orientation consistent across all panels and use one production LOT per vehicle to avoid texture mismatch between panels.
• Overlap: 3 to 4 mm
• Avoid overstretching during application, which can distort the brushed texture
• Post-heat: 100°C
• Remove the protective cap before installing
• Professional installation strongly recommended for the best result and to keep the warranty valid
• Aftercare: hand wash with a pH-neutral shampoo (pH 3 to 11). The brushed grain can trap dirt, so rinse thoroughly and dry along the grain direction. Avoid waxes, solvents, and petroleum-distillate products, and never use automatic washes, brushes, or high-pressure washers.

All TeckWrap statements, technical information, and recommendations are based on tests believed to be reliable but do not constitute a guarantee or warranty. All products are sold with the understanding that the buyer has independently determined the suitability of the products for their purpose.

TeckWrap products are warranted to be free of defects in material for the period of shelf life. In case of defects, TeckWrap will replace the product or compensate at its sole discretion. This is the exclusive obligation of TeckWrap Inc.

Warranty does not cover normal wear, transportation, labor, or consequential damages. Coverage requires proper storage, professional installation, and maintenance in line with TeckWrap's care guidance, and does not apply to films installed on non-OEM, repainted, or damaged surfaces. If you notice cracking, lifting, edge failure, or other defects, contact your installer promptly for assessment.

The brushed texture is more sensitive to abrasion within the grain and can trap dirt more readily than a flat finish. This is a normal characteristic of a textured film and is not covered.

Removal from aged, repainted, or poorly bonded factory paint may lift paint or clear coat. TeckWrap is not responsible for the condition of the underlying paint upon removal.

Screen images may vary, refer to physical color swatches. Use the same production LOT for color consistency. Scratches during application or daily use are not covered.