PAPAYA ORANGE (CG54-HD) Vinil envoltório

Film construction

• Film type: high-grade polymeric hybrid film with air-release channels
• Film thickness: 110 μm (0.11 mm)
• Liner thickness: 142 μm (0.142 mm)
• Liner: transparent plastic release liner
• Adhesive: Henkel solvent-based acrylic, ultra weather-resistant, 1000 to 3000 cps viscosity, 12 μm dry
• Finish: super gloss, solid color
• Roll width: 1.52 m (5 ft)
• Roll length: 18 m standard, 23 m extended rolls available

Performance

• Service temperature: -35°C to +35°C
• Release force: 0.18 N/25mm (standard 0.10 to 0.30)
• Initial tack: 1015 g/25mm (standard 800 to 1500)
• 180° peel strength: 8.1 N/25mm (standard ≥4.9)
• Adhesion strength: 70 (standard ≥60, no shifting)
• High temperature aging (65°C, 7 days): no adhesive residue
• Low temperature aging (-65°C, 10 days): no adhesive residue
• Storage: 2 year shelf life at +10°C to +20°C, 50% relative humidity, in original packaging, away from direct sunlight

Warranty

Built for long-term outdoor use, with up to 3 years of durability on vertical panels and around 2 years across a full wrap, depending on climate zone. Horizontal surfaces such as roofs, hoods, and bonnets take the most sun and weather and carry a shorter expected life. The warranty covers manufacturing defects such as bubbling, cracking, and adhesive failure when the film is properly stored, professionally installed, and maintained per the care guidance. It does not cover abrasion, scratches, gloss change, or normal wear. Heat-removable within 2 years for the cleanest removal, with minimal adhesive residue.

• Surface: apply only to a clean, sound, fully cured OEM factory finish. Repainted, primed, aftermarket, or damaged surfaces can affect adhesion and removal and fall outside warranty coverage.
• Remove the top protective PET layer before installation. Do not store rolls with the top layer on as this causes tunneling in the film.
• Apply at +17°C to +23°C
• Tools: squeegee with soft buffer, knife, masking tape, heat gun, gloves
• Conformability: smooth and medium-curved surfaces
• Post-heat: 95°C
• Cure: 24 hrs above 10°C (48 hrs at room temperature recommended)
• Overlap: 3 to 4 mm
• Non-directional film
• Avoid overstretching during application
• Professional installation strongly recommended for the best result and to keep the warranty valid
• Aftercare: hand wash with a pH-neutral shampoo (pH 3 to 11). Avoid waxes, solvents, and petroleum-distillate products, and never use automatic washes, brushes, or high-pressure washers.

All TeckWrap statements, technical information, and recommendations are based on tests believed to be reliable but do not constitute a guarantee or warranty. All products are sold with the understanding that the buyer has independently determined the suitability of the products for their purpose.

TeckWrap products are warranted to be free of defects in material for the period of shelf life. In case of defects, TeckWrap will replace the product or compensate at its sole discretion. This is the exclusive obligation of TeckWrap Inc.

Warranty does not cover normal wear, transportation, labor, or consequential damages. Coverage requires proper storage, professional installation, and maintenance in line with TeckWrap's care guidance, and does not apply to films installed on non-OEM, repainted, or damaged surfaces. If you notice cracking, lifting, edge failure, or other defects, contact your installer promptly for assessment.

Removal from aged, repainted, or poorly bonded factory paint may lift paint or clear coat. TeckWrap is not responsible for the condition of the underlying paint upon removal.

Aftermarket waxes, sealants, and ceramic coatings are applied at the owner’s discretion. Damage caused by aftermarket products is not covered.

Screen images may vary, refer to physical color swatches. Use the same production LOT for color consistency. Scratches during application or daily use are not covered.